72 F250 CS..truck bed uneven 1-2 in.
Moderator: FORDification
-
- New Member
- Posts: 18
- Joined: Thu Oct 31, 2013 9:50 am
72 F250 CS..truck bed uneven 1-2 in.
Bought this awesome truck a few weeks ago and I am noticing that the bed is uneven to the left 1 or 2 in. Anybody ever run into that before? Any idea what could cause that?
- chad67
- Blue Oval Fan
- Posts: 680
- Joined: Sat Dec 29, 2012 11:21 am
- Location: Sullivan, MO
Re: 72 F250 CS..truck bed uneven 1-2 in.
Check the mounts for the bed for damage or decay. Then check your cab mounts, the bed on my truck doesn't line up because the cab is tilted. At first glance it appears the bed is out of whack. Use a tape measure in between your cab and bed to measure from the top of your frame rails to the top of your bed-it should be the same on both sides. If it is, do the same for the cab, top of frame to bottom of rear glass on both sides.
1967 F100 SWB
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
- chad67
- Blue Oval Fan
- Posts: 680
- Joined: Sat Dec 29, 2012 11:21 am
- Location: Sullivan, MO
Re: 72 F250 CS..truck bed uneven 1-2 in.
In review, I may have misunderstood. If you are talking about a shift to the side, do the same measurement from the outside of the frame rails to the outside of the bed and cab.
1967 F100 SWB
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
-
- New Member
- Posts: 18
- Joined: Thu Oct 31, 2013 9:50 am
Re: 72 F250 CS..truck bed uneven 1-2 in.
Yeah when you stand at the rear and look towards the front, you see that the bed cab is leaning towards the left an inch or two.
-
- New Member
- Posts: 18
- Joined: Thu Oct 31, 2013 9:50 am
Re: 72 F250 CS..truck bed uneven 1-2 in.
the box isn't in line with the rear window..tilted to the left about an inch.
- Calfdemon
- 100% FORDified!
- Posts: 2672
- Joined: Tue May 25, 2010 11:31 pm
- Location: California, Santa Clarita
Re: 72 F250 CS..truck bed uneven 1-2 in.
It may be a very simple fix.. There is a little bit of play in the bed bolts for adjusting purposes... Just loosen all of the bed bolt and then adjust the bed left and right until it sits where you want it. Then tighten all of the bolts back down.
-Rich
Current toys -
69 Ford F350 Crew Cab - 460 / C6 - http://i253.photobucket.com/albums/hh67 ... lqgskp.jpg
31 Ford Vicky - 1955 270 Red Ram Hemi / 4 speed - http://i253.photobucket.com/albums/hh67 ... bsibvn.jpg
Former toys -
67 Pontiac Firebird 400 convertible (sold 9/13) - http://i253.photobucket.com/albums/hh67 ... bird-1.jpg
67 Ford Fairlane GT - 390 / 4 speed (sold 7/15) - http://i253.photobucket.com/albums/hh67 ... c5hu8z.jpg
Current toys -
69 Ford F350 Crew Cab - 460 / C6 - http://i253.photobucket.com/albums/hh67 ... lqgskp.jpg
31 Ford Vicky - 1955 270 Red Ram Hemi / 4 speed - http://i253.photobucket.com/albums/hh67 ... bsibvn.jpg
Former toys -
67 Pontiac Firebird 400 convertible (sold 9/13) - http://i253.photobucket.com/albums/hh67 ... bird-1.jpg
67 Ford Fairlane GT - 390 / 4 speed (sold 7/15) - http://i253.photobucket.com/albums/hh67 ... c5hu8z.jpg
- chad67
- Blue Oval Fan
- Posts: 680
- Joined: Sat Dec 29, 2012 11:21 am
- Location: Sullivan, MO
Re: 72 F250 CS..truck bed uneven 1-2 in.
I would take all the measurements I mentioned to be sure it's the bed. Always measure from the frame, I did the same for my truck-bed was straight, the cab was tilted. Your eyes can deceive you.
1967 F100 SWB
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
- chad67
- Blue Oval Fan
- Posts: 680
- Joined: Sat Dec 29, 2012 11:21 am
- Location: Sullivan, MO
Re: 72 F250 CS..truck bed uneven 1-2 in.
Here's a shot of mine when I got it. The bed and cab don't line up because my cab mounts are gone. The bed is dead straight, the cab is out by almost 2 inches.
You do not have the required permissions to view the files attached to this post.
1967 F100 SWB
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
1991 Thunderbird 5.0 with fully ported gt40 heads, cobra intake (also ported) and a trickflow stage 2 cam, manual steering, and custom 3" exhaust
-
- New Member
- Posts: 57
- Joined: Mon Nov 21, 2005 12:12 am
- Location: Washington
Re: 72 F250 CS..truck bed uneven 1-2 in.
Mine is off by about 1/2" and I was hoping new cab rubber mounts might fix it. If the mount flanges are not wasted and it still does not line up I will shim the bed.chad67 wrote:Here's a shot of mine when I got it. The bed and cab don't line up because my cab mounts are gone. The bed is dead straight, the cab is out by almost 2 inches.
67 F250 4x4