
33x12.50 on a 68 2wd CS
Moderator: FORDification
- kilog55
- Preferred User
- Posts: 399
- Joined: Sun Feb 10, 2008 1:07 pm
- Location: Lenoxville, Pennsyltucky
33x12.50 on a 68 2wd CS
anyone know if they will fit off hand or should i just go and throw em on and see 

1968 F250 Ranger 2wd 472ci TH400 Caddy powered.
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437
- ForingaMex
- Blue Oval Fan
- Posts: 590
- Joined: Thu May 21, 2009 8:18 pm
- Location: Ontario, Canada
Re: 33x12.50 on a 68 2wd CS
I can't tell you for sure but I doubt it. I just installed 31x10.5 on my 72 and they fit nice but I'm pretty sure any bigger and they would rub, especially in the front.
-Jake
"Better to remain silent and be thought a fool than to speak out and remove all doubt." -Abraham Lincoln
-02 Dodge Ram Quad Cab
-72 Ford F100 LWB 390/C6 (Retired for now till I can rebuild/transform it)
-2000 Ford Windstar (Family Vehicle)
-92 VW Beetle (Mexican)
"Better to remain silent and be thought a fool than to speak out and remove all doubt." -Abraham Lincoln
-02 Dodge Ram Quad Cab
-72 Ford F100 LWB 390/C6 (Retired for now till I can rebuild/transform it)
-2000 Ford Windstar (Family Vehicle)
-92 VW Beetle (Mexican)
- gregamorton
- Blue Oval Fanatic
- Posts: 935
- Joined: Mon Jun 15, 2009 7:57 pm
- Location: Blossom TX
Re: 33x12.50 on a 68 2wd CS
I put some 16.5x10s on my crew today with 33x12.50s and they fit under truck and have about 2" before they touch the inner bed area.




1967 mercury F350 7.3 IDI ats turbo kit c6 gear vendor overdrive 3.73s rolling on 19.5s
1971 sport custom on 1979 f350 highboy frame 460 c6 np205 dana 60s 3.54s
1974 F100 baby blue & rust 240 3 speed 3.70s sitting on the ground!
1990 F250 extended cab FI460 e40d 3.55s daily driver
Possibly looking for my next bump right now!
1971 sport custom on 1979 f350 highboy frame 460 c6 np205 dana 60s 3.54s
1974 F100 baby blue & rust 240 3 speed 3.70s sitting on the ground!
1990 F250 extended cab FI460 e40d 3.55s daily driver
Possibly looking for my next bump right now!
- kilog55
- Preferred User
- Posts: 399
- Joined: Sun Feb 10, 2008 1:07 pm
- Location: Lenoxville, Pennsyltucky
Re: 33x12.50 on a 68 2wd CS
yeah these are 16.5x9.75 they fit the 79 with no lift fine but thats a 4x4 but a low boy as well.
1968 F250 Ranger 2wd 472ci TH400 Caddy powered.
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437
- Hawkrod
- Blue Oval Fanatic
- Posts: 939
- Joined: Tue Mar 01, 2005 12:17 am
- Location: Apple Valley, California
- Contact:
Re: 33x12.50 on a 68 2wd CS
They fit fine on the rear but may rub on the front. I have had several trucks they fit on the front no trouble and several others where I had to roll the lower leading edge of the fender. I like the way they look though and have them on several trucks. Hawkrod
39 Ford Dlx Cpe
59 Tbird 430
60 Lincoln
(2)62 Tbirds
(3)68 Cougar XR7-G's
69 Cougar 428CJ 4 speed
77 1/2 F250 4X4
86 SVO
76 F250 Crew Cab
67 F250 Ranger
http://www.supermotors.org/registry/veh ... 9&detail=1
59 Tbird 430
60 Lincoln
(2)62 Tbirds
(3)68 Cougar XR7-G's
69 Cougar 428CJ 4 speed
77 1/2 F250 4X4
86 SVO
76 F250 Crew Cab
67 F250 Ranger
http://www.supermotors.org/registry/veh ... 9&detail=1
- kilog55
- Preferred User
- Posts: 399
- Joined: Sun Feb 10, 2008 1:07 pm
- Location: Lenoxville, Pennsyltucky
Re: 33x12.50 on a 68 2wd CS
ill just have to throw em en and see then
1968 F250 Ranger 2wd 472ci TH400 Caddy powered.
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437
1979 F250 Ranger 4X4 400ci T18
anyone need a 60x24x24 flatbed semi toolbox?
my gallery - http://www.fordification.com/galleries/ ... ?cat=10437