Worn Tie-Rod Ends?
Moderator: FORDification
-
- New Member
- Posts: 161
- Joined: Mon May 08, 2006 4:12 am
- Location: Tennessee, New Hope
Worn Tie-Rod Ends?
What are some symptoms of worn tie-rod ends? Also, is there any way that I could check to see if the tie-rod ends are worn? I've got a wierd vibration going on in the front end and I'm trying to narrow down the possibilities.
-
- Blue Oval Fan
- Posts: 666
- Joined: Sun Sep 12, 2004 1:16 am
- Location: West Michigan area
- Contact:
re: Worn Tie-Rod Ends?
either that or bearings
Ford Is The Mountain That The Rock fell Off Of.
72 F-250 Camper Special 390 Stroker 419 CID 420 HP Natural Asp 200 HP NOS C-6 Dana 60 4.10
96 F-150 XLT 4X4 5.8 Heavy Duty 4EOD
72 F-250 Camper Special 390 Stroker 419 CID 420 HP Natural Asp 200 HP NOS C-6 Dana 60 4.10
96 F-150 XLT 4X4 5.8 Heavy Duty 4EOD
- ToughOldFord
- 100% FORDified!
- Posts: 1913
- Joined: Mon Jul 25, 2005 10:47 pm
- Location: Communist California, USA
re: Worn Tie-Rod Ends?
Jack up the wheel and grab the tire and shake it to your left and right. Do not pull truck down on yourself. Observe where the tire rod joint hooks up to the spindle arm, (if that's what it's called), if you see excessive movement, meaning pretty much any, then it's time for a new one.
- Galaxie64
- New Member
- Posts: 203
- Joined: Tue Mar 21, 2006 11:51 pm
- Location: Wyoming
re: Worn Tie-Rod Ends?
When they get really bad you will be constantly correcting the wheel when going down the road, it usually is so gradual you don't relize how much correction you were doing until you drive it with new ends.
'68 F150 2wd
'72 F250 2wd Camper Special (400/C6/4bbl)
'64 Galaxie 500 (3524bbl/57K miles)
'92 Grand Marquis (mostly stock 4.6L)
'97 F150 (heavily modded 5.4L)
'48 F1 (Flat 6)
'51 F3 (Flat V8 )
'56 F350 (engineless)
** Chuck Norris has counted to infinity -- twice. **
'72 F250 2wd Camper Special (400/C6/4bbl)
'64 Galaxie 500 (3524bbl/57K miles)
'92 Grand Marquis (mostly stock 4.6L)
'97 F150 (heavily modded 5.4L)
'48 F1 (Flat 6)
'51 F3 (Flat V8 )
'56 F350 (engineless)
** Chuck Norris has counted to infinity -- twice. **
-
- Preferred User
- Posts: 484
- Joined: Thu Jul 22, 2004 9:05 pm
- Location: Ridgecrest, CA
re: Worn Tie-Rod Ends?
Might not hurt to just replace them anyway, except they are a little expensive. If you remove the tierod ends from your truck, see if you can move them by hand. If they move without a lot of effort, they are worn out.
Former owner of 70 LB SportCustom and a 71 SB SportCustom. Looking for a replacement bump!
- FORDification
- Site & Forum Admin
- Posts: 8050
- Joined: Sun Jul 11, 2004 12:52 am
- Location: Kansas, Wellsville
- Contact:
re: Worn Tie-Rod Ends?
If they look like this, they probably should be replaced:
From a parts truck:


From a parts truck:

____| \__
-O-----O- Keith
'67 F-100 2WD SWB ~ '69 F-100 4WD SWB w/7" chop ~ 1975 F-250 Ranger XLT Supercab Camper Special



My '67 restoration video
-> Posting and you! <-a MUST watch for all!!
-O-----O- Keith
'67 F-100 2WD SWB ~ '69 F-100 4WD SWB w/7" chop ~ 1975 F-250 Ranger XLT Supercab Camper Special



My '67 restoration video
-> Posting and you! <-a MUST watch for all!!
-
- New Member
- Posts: 155
- Joined: Sun Sep 10, 2006 2:17 pm
- Location: Washington, Vancouver
- ToughOldFord
- 100% FORDified!
- Posts: 1913
- Joined: Mon Jul 25, 2005 10:47 pm
- Location: Communist California, USA
Re: re: Worn Tie-Rod Ends?
Yep.bugser wrote:Nah,they just need a little grease.


-
- Blue Oval Fanatic
- Posts: 826
- Joined: Mon Nov 21, 2005 1:31 am
re: Worn Tie-Rod Ends?
Yup, those look like they have seen better days.
Two it takes to ck it out. One to wiggle the steering wheel back and forth
and another to eyeball the motion going on in the steering. Look at the
rod ends as your helper wiggles the wheel. Is there any lost motion or
"play" in them? If you see it or hear noise theres a problem. If you have
any doubts about a part being sub-par, replace it with new.
Be safe.
Also, your tires will last a lot longer if the front end is got tight parts. $$$
Two it takes to ck it out. One to wiggle the steering wheel back and forth
and another to eyeball the motion going on in the steering. Look at the
rod ends as your helper wiggles the wheel. Is there any lost motion or
"play" in them? If you see it or hear noise theres a problem. If you have
any doubts about a part being sub-par, replace it with new.
Be safe.
Also, your tires will last a lot longer if the front end is got tight parts. $$$