I am looking for 1967-1972 Ford truck parts....
I need:
passenger's side stainless missing my bump trim and bottom of the door and front fender
steering wheel (61-70 I hate the plastic look in the center of the 71-72) prefer fancy horn rings!!
rear sliding window
Grille (1970-72) ONLY This has to be in very good shape with the shine on it and I am willing to pay accordingly. My current grille is fine, but lost its luster.
original radio yes I'm a sucker for original look (will hide a new radio in the glove box)
Steering column (from a manual floor shift truck)
parts wanted, steering wheel, etc
Moderator: FORDification
- wndsofchng06
- Preferred User
- Posts: 402
- Joined: Fri Jun 01, 2012 7:41 pm
- Location: Durham, NC
- gregamorton
- Blue Oval Fanatic
- Posts: 935
- Joined: Mon Jun 15, 2009 7:57 pm
- Location: Blossom TX
Re: parts wanted, steering wheel, etc
where are you located? I have a super nice 70 grill but I am not shipping these any more due to damage. I am in northeast tx.
1967 mercury F350 7.3 IDI ats turbo kit c6 gear vendor overdrive 3.73s rolling on 19.5s
1971 sport custom on 1979 f350 highboy frame 460 c6 np205 dana 60s 3.54s
1974 F100 baby blue & rust 240 3 speed 3.70s sitting on the ground!
1990 F250 extended cab FI460 e40d 3.55s daily driver
Possibly looking for my next bump right now!
1971 sport custom on 1979 f350 highboy frame 460 c6 np205 dana 60s 3.54s
1974 F100 baby blue & rust 240 3 speed 3.70s sitting on the ground!
1990 F250 extended cab FI460 e40d 3.55s daily driver
Possibly looking for my next bump right now!
- Ranchero50
- Moderator
- Posts: 5799
- Joined: Wed Nov 08, 2006 7:02 pm
- Location: Maryland, Hagerstown
- Contact:
Re: parts wanted, steering wheel, etc
I have a stock '68 Ford AM radio with the bezels and knobs, speaker and mounting bars. I haven't tested it to see if it works but if it's just cosmetic, it looks fine. $60+shipping
What lower trim do you have? Take a picture if possible
What lower trim do you have? Take a picture if possible
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
- wndsofchng06
- Preferred User
- Posts: 402
- Joined: Fri Jun 01, 2012 7:41 pm
- Location: Durham, NC
Re: parts wanted, steering wheel, etc
I'm in Charlotte, NC..... so texas is a bit far....
radio looks nice.... does the 68 mount the same as the 72?
I attached a photo of the lower driver's side where trim is present, if it doesn't show large enough I will take another when it's light outside
radio looks nice.... does the 68 mount the same as the 72?
I attached a photo of the lower driver's side where trim is present, if it doesn't show large enough I will take another when it's light outside
You do not have the required permissions to view the files attached to this post.
-
- New Member
- Posts: 100
- Joined: Tue Oct 04, 2011 2:39 pm
- Location: North Carolina
Re: parts wanted, steering wheel, etc
I have sliding rear window in good condition. I am in the statesville area if you would like to meet to take a look
- basketcase0302
- 100% FORDified!
- Posts: 6805
- Joined: Thu Jan 26, 2006 7:11 am
- Location: Hawthorne, Florida
Re: parts wanted, steering wheel, etc
PM sent
Jeff
http://www.fordification.com/forum/view ... 22&t=46251
SOLD-71 F-350 dually flatbed, 302 / .030 over V-8 with a "baby"C-6, B & M truckshifter, Dana70/4.11 ratio, intermittent wipers, tilt steering, full LED lighting on the flat bed, and no stereo yet (this way I can hear the rattles to diagnose)! SOLD!
Many Ford bumps / one 76' EB / and several dents through the years.
A lot of "oddball" Ford parts collected from working on them for 34 years now!
2008 Ford Escape 4 x 4
http://www.fordification.com/forum/view ... 22&t=46251
SOLD-71 F-350 dually flatbed, 302 / .030 over V-8 with a "baby"C-6, B & M truckshifter, Dana70/4.11 ratio, intermittent wipers, tilt steering, full LED lighting on the flat bed, and no stereo yet (this way I can hear the rattles to diagnose)! SOLD!
Many Ford bumps / one 76' EB / and several dents through the years.
A lot of "oddball" Ford parts collected from working on them for 34 years now!
2008 Ford Escape 4 x 4
- Ranchero50
- Moderator
- Posts: 5799
- Joined: Wed Nov 08, 2006 7:02 pm
- Location: Maryland, Hagerstown
- Contact:
Re: parts wanted, steering wheel, etc
wndsofchng06 wrote:I'm in Charlotte, NC..... so texas is a bit far....
radio looks nice.... does the 68 mount the same as the 72?
I attached a photo of the lower driver's side where trim is present, if it doesn't show large enough I will take another when it's light outside
Yep, radio mounts the same.
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
-
- New Member
- Posts: 11
- Joined: Sat Jun 09, 2012 12:11 am
- Location: Albuquerque NM
Re: parts wanted, steering wheel, etc
sent you a PM about the steeringwheel in my 1970
Tracy
Tracy