Changing Oil Pan for better drain plug location

Engine, ignition, fuel, cooling, exhaust

Moderators: Ranchero50, DuckRyder

Post Reply
User avatar
tylerb43
Preferred User
Preferred User
Posts: 492
Joined: Fri Nov 14, 2008 2:54 pm
Location: Union, MO

Changing Oil Pan for better drain plug location

Post by tylerb43 »

So I didn't really notice it while building or installing the engine, but the drain plug location is in a horrible spot, right above the cross member. My truck had an old 390 (non-original) that sat for decades, so I opted to start with a second 390 I had, which I was told came from a '73 Galaxie. I knew the fullsize cars and the 2wd trucks were both front sumps, and I didn't study it much further than that.

But after I got the engine onto the chassis, I realized the drain plug just won't work there. It's located on the passenger side, about 1" forward of the rear of the sump, facing outboard. Even if I could get the plug out, it would dump oil all over the crossmember - not cool.

In this picture you can also see the indented areas on the rear of the pan, these were to clear the car's steering linkage.

Image

Kinda dark, but click on this to blow it up, and you can kinda see the issue.

Image

So I went back to my old 390 that I had in the truck back in high school, and sure enough, it's drain plug was different. It's on the driver's side, at the rear corner of the sump, facing outboard and aft. Much better.

Image

So I pulled the pan off the old motor and glass beaded it, and painted it up. As you can see it's part number is C7AE-6675A, with a date code of 08-10-72. I knew the old 390 was not original in my '69, which came with a 360.

Image

Image

Image

I also ordered a Fumoto F-101N drain plug (with the nipple for attaching a short hose). Hopefully this will help solve any oil drain issues I would've had.

http://www.amazon.com/gp/product/B003VC ... 00_details

Have any of you other guys ran into this?? Any performance differences with switching the pans? (I noticed they have different style baffles in them) I'm not building a race truck, so I doubt I'll care... :?
User avatar
1972hiboy
100% FORDified!
100% FORDified!
Posts: 2421
Joined: Thu Sep 09, 2010 5:44 pm
Location: California, Santa Cruz

Re: Changing Oil Pan for better drain plug location

Post by 1972hiboy »

I think you did the smart thing putting a truck pan back on there. If I remeber correctly the oil will still be over the cross member. Im hoping you put a couple pics up to show your fumoto valve all installed in the pan. DOnt think there is much differance performce wise regarding the baffles. the car pan was just probably altered a little bit to make it fit the best way in the car it was in and same for the truck pan.
Rich
1973 f350 super c/s 460/c6 22k orig miles
1972 f350 srw crewcab special 390
1972 f250 4x4 sport custom 390fe Red
1972 f250 4x4 custom 360 FE " Ranger Ric"
1972 f250 4x4 custom 84k og miles 390
1971 f250 4x4 sport custom 56k og miles. 360
1970 f250 4x4 428 fe hp60 205 d60
Dont eat yellow snow.....
User avatar
1972hiboy
100% FORDified!
100% FORDified!
Posts: 2421
Joined: Thu Sep 09, 2010 5:44 pm
Location: California, Santa Cruz

Re: Changing Oil Pan for better drain plug location

Post by 1972hiboy »

duplicate post
Last edited by 1972hiboy on Tue Mar 27, 2012 12:32 pm, edited 1 time in total.
Rich
1973 f350 super c/s 460/c6 22k orig miles
1972 f350 srw crewcab special 390
1972 f250 4x4 sport custom 390fe Red
1972 f250 4x4 custom 360 FE " Ranger Ric"
1972 f250 4x4 custom 84k og miles 390
1971 f250 4x4 sport custom 56k og miles. 360
1970 f250 4x4 428 fe hp60 205 d60
Dont eat yellow snow.....
User avatar
Ranchero50
Moderator
Moderator
Posts: 5799
Joined: Wed Nov 08, 2006 7:02 pm
Location: Maryland, Hagerstown
Contact:

Re: Changing Oil Pan for better drain plug location

Post by Ranchero50 »

Robroy had a short peice of pipe welded on so it would drain away from the crossmember.
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue

Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
User avatar
colnago
100% FORDified!
100% FORDified!
Posts: 1882
Joined: Tue Jun 14, 2011 8:48 pm
Location: Ridgecrest, CA

Re: Changing Oil Pan for better drain plug location

Post by colnago »

I also understand that you can use a pan from an FT engine. This has a rear drain. Dunno if it has a front or rear sump, though; the pan looks pretty flat on the bottom to me.

Joseph
"Sugar", my 1967 Ford F250 2WD Camper Special, 352FE, Ford iron "T" Intake with 1405 Edelbrock, Duraspark II Ignition, C6 transmission, front disc brake conversion.
User avatar
basketcase0302
100% FORDified!
100% FORDified!
Posts: 6805
Joined: Thu Jan 26, 2006 7:11 am
Location: Hawthorne, Florida

Re: Changing Oil Pan for better drain plug location

Post by basketcase0302 »

My 360 that was in my truck was also the same way, (drain over and onto the crossmember) and worse!
The PO had actually stripped out the threads on the pan due to it being such a PIB to work with. :hw:
So what does any low budget redneck do-that will be yanking the engine out soon anyway...
JB Weld the plug into the pan, (so it will hold oil) and use a marine pump to change the oil. :oops:

Seems like I remember reading here the car pans were all front sump? Still doesn't answer the pan in my truck, as it really appeared to be the original engine when I yanked it out? :hmm:
Jeff
http://www.fordification.com/forum/view ... 22&t=46251
SOLD-71 F-350 dually flatbed, 302 / .030 over V-8 with a "baby"C-6, B & M truckshifter, Dana70/4.11 ratio, intermittent wipers, tilt steering, full LED lighting on the flat bed, and no stereo yet (this way I can hear the rattles to diagnose)! SOLD!
Many Ford bumps / one 76' EB / and several dents through the years.
A lot of "oddball" Ford parts collected from working on them for 34 years now!
2008 Ford Escape 4 x 4
User avatar
tylerb43
Preferred User
Preferred User
Posts: 492
Joined: Fri Nov 14, 2008 2:54 pm
Location: Union, MO

Re: Changing Oil Pan for better drain plug location

Post by tylerb43 »

Thanks for the replies, guys.

Rich, I definitely will post some pics when I get the Fumoto valve installed, I can't wait to see it myself. :thup:

And Jeff, yes, car pans are front sump, as are the 2wd pans for our trucks, I guess my point was that just because they're both front sump doesn't make them form-fit-function identical, which is what it seems as you read through some of the posts about pans on this forum. And your engine may be original, but I guess it's possible that the pan could've been replace at some point because of damage or something? :hmm:

Joseph - I've also heard that the FT pans will fit the engine, and I think some are called "full sump" (pretty flat on the bottom). However, on our trucks (2wd) you may have clearance issues to the steering linkage, especially at a full lock turn.

Do you guys know if there are different oil capacity pans (talking car and truck front-sumps only here). Is the truck pan I'm painting above a 5 qt? I'm planning on doing a side by side comparison with it and the Galaxie pan once I get it out, and maybe a volume test, just to satisfy my curiosity if nothing else. :?

:fr:
cdeal28078
100% FORDified!
100% FORDified!
Posts: 1982
Joined: Mon Aug 15, 2005 8:45 am
Location: North Carolina, Huntersville

Re: Changing Oil Pan for better drain plug location

Post by cdeal28078 »

My 71 came with a 302 stock and I am pretty sure it was a front sump pan with the drain plug on the back side of the pan. It still made a mess of the cross member when draining the oil.
The 460 in it now came from a 76-77 F150 and is a front sump pan with the drain plug on the back side of the pan and still makes a mess. I saw a fold-able piece of plastic somewhere ether on TV or in the store that you can fold and put in place so the oil won't drain on the cross member. I need to get one for myself. Might be worth it for many of us to get one. lol
Clint
71 F100 SportCustom
460 C6. Disc Brake/Power-steering/automatic Swap. 3.00
1986 Bronco 5.0 AOD
User avatar
tylerb43
Preferred User
Preferred User
Posts: 492
Joined: Fri Nov 14, 2008 2:54 pm
Location: Union, MO

Re: Changing Oil Pan for better drain plug location

Post by tylerb43 »

Hey guys, I got the quick drain valve and installed it on the replacement pan. I'll install the pan on the engine soon, just waiting on the new pan gasket. I have a feeling I'll get impatient and do a test fit install just to see how much clearance there is to the crossmember.

Image

Image
User avatar
colnago
100% FORDified!
100% FORDified!
Posts: 1882
Joined: Tue Jun 14, 2011 8:48 pm
Location: Ridgecrest, CA

Re: Changing Oil Pan for better drain plug location

Post by colnago »

Ooh, yes! Keep us posted. I almost bought one of these valves, but didn't know if I would run into fitment issues. Definitely let us know.

Joseph
"Sugar", my 1967 Ford F250 2WD Camper Special, 352FE, Ford iron "T" Intake with 1405 Edelbrock, Duraspark II Ignition, C6 transmission, front disc brake conversion.
User avatar
robroy
100% FORDified!
100% FORDified!
Posts: 3768
Joined: Sun Jul 06, 2008 4:36 pm
Location: California, Salinas

Re: Changing Oil Pan for better drain plug location

Post by robroy »

Good day TylerB43 and Jamie,

Jamie, thanks for mentioning my modification! Actually, now that I've actually used it a few times, it didn't practically work out as well as I'd hoped. That's because the pipe section I had welded on wasn't located at the true bottom of the pan. I tried doing the oil change on a hill once, but decided to never do that again because I felt too nervous about #50 rollin' over me!

TylerB43, I love the looks of that valve you found! Wow. I admit that my first thought's a little paranoia about a small tree branch or something pressing up against it and drainin' the oil at an inopportune time though. May I know how stiff that lever is? Anything special preventing it from being pressed on by debris under the truck? I guess that's an unlikely scenario, but hey it's the oil. :)

Robroy
mrollings53
Blue Oval Fan
Blue Oval Fan
Posts: 617
Joined: Mon May 10, 2010 6:09 pm
Location: Tacoma, WA

Re: Changing Oil Pan for better drain plug location

Post by mrollings53 »

From the picture it looks like you have to pull the lever down and then turn it to open the valve. Looks like there is also a spring on the lever, which I think would apply pressure to keep it seated in the closed position.
IMG_2137.jpg
You do not have the required permissions to view the files attached to this post.
Common Sense is an Uncommon Virtue
mjhaltom
Preferred User
Preferred User
Posts: 400
Joined: Thu Aug 03, 2006 7:24 am
Location: Georgia, Elberton

Re: Changing Oil Pan for better drain plug location

Post by mjhaltom »

Nice fix! But you realize you are giving up the free rust preventative coating for your front crossmember that would be reapplied at ever oil change!
2015 lifted Toyota tundra 4.6 4wd
2002 Toyota Sequoia 2wd 4.7 auto
1989 Ford F150
1979 Chevrolet C10 350/TH400 14 bolt "Big 10" (DD)
1972 F100 parts truck long bed
1971 F100 2WD LWB 302 aod 3.70 9inch PS pb
1966 International Scout 800
1954 GMC rat rod project Scout frame, inline 6, T90 4X4
1953 Chevrolet Tin Woody
1946 Hudson BigBoy Pickup-ratrod project
User avatar
tylerb43
Preferred User
Preferred User
Posts: 492
Joined: Fri Nov 14, 2008 2:54 pm
Location: Union, MO

Re: Changing Oil Pan for better drain plug location

Post by tylerb43 »

mrollings53 wrote:From the picture it looks like you have to pull the lever down and then turn it to open the valve. Looks like there is also a spring on the lever, which I think would apply pressure to keep it seated in the closed position.
IMG_2137.jpg
That's exactly right, mrollings53! Opening the valve is a two-part movement. One - lift the lever up away from the valve, and Two - turn to open just as you say. In the picture of the valve in my hand above, the valve is open and you can see the spring compressed. The little lever is pretty hard to turn, it kinda hurts your finger tip to do it.

I'm a 'what if' guy too, Robroy. I'm an engineer and it's in my nature to think about what "could" happen, and then design to prevent it. If you had this valve in your hand, the scenario of the valve opening on it's own becomes Highly unlikely, and nearly impossible.
mjhaltom wrote:Nice fix! But you realize you are giving up the free rust preventative coating for your front crossmember that would be reapplied at ever oil change!
HA! Good one, I guess you're right, that may be a downside to this fix, depending on how you look at it, but it's something I'm willing to do without :D
User avatar
tylerb43
Preferred User
Preferred User
Posts: 492
Joined: Fri Nov 14, 2008 2:54 pm
Location: Union, MO

Re: Changing Oil Pan for better drain plug location

Post by tylerb43 »

Hey guys, I got the replacement pan with valve installed yesterday. It's going to work out great. You could either attach a short piece of hose every time you change the oil. Or just leave the hose on there all the time, which is what I believe I'm going to do. Check it out.

Before I started, I used my Mity-vac fluid extractor to suck all the oil out of the pan so I didn't have to use the drain plug and make the huge mess I'm trying to prevent with this fix.

Getting the 390 up in the air. (I removed both engine mount nuts and the single trans mount bolt (C6))
Image

View from the underside. (cleaning the gasket surface) ooh - I need to paint those crank pulley bolt heads! :wink:
Image

And here are a couple to show clearance to the valve.
From the aft side looking forward.
Image

Looking aft and slightly inboard.
Image

I did notice that with the engine set back down on the mounts, I didn't have clearance to the crossmember to remove and reinstall the valve, so if you have this same pan, and want to install this valve, you would have to raise the engine a little to screw in the valve (only like a 1/4"-1/2" or so). You may be able to unbolt the left side mount only, and lift that side of the engine...it doesn't need much at all.

Here's to clean oil changes!!! :thup: :thup:
Post Reply