Im in need of new tie rods, and the only place I could find them is right here: http://oem.thepartsbin.com/parts/thepar ... nd&dp=true
I had no idea they would be this expensive. Since I need inner and outer tie rod ends, Im going to be spending over 90 bucks. Should I get these??? also, does anyone know why there is the 4wd outer tie rod for $45.35 and then another 4wd outer tie rod is for $125.70?
tie rods
Moderator: FORDification
- boots
- Preferred User
- Posts: 411
- Joined: Sat May 21, 2005 5:13 pm
- Location: Illinois
tie rods
Ethan
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
-
- 100% FORDified!
- Posts: 22329
- Joined: Sun Aug 28, 2005 8:17 pm
- Location: Kansas, Ottawa
- Contact:
- boots
- Preferred User
- Posts: 411
- Joined: Sat May 21, 2005 5:13 pm
- Location: Illinois
yes , thank youfordman wrote:wait until saturdaynight i'll let you know something. i found a few trucks i might be able to get or get parts from. 67 right?
Ethan
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
- hardtailjohn
- Preferred User
- Posts: 422
- Joined: Tue Dec 07, 2004 10:24 pm
- Location: Montana, Marion
re: tie rods
Just be glad you don't have the F100 4x4!
John H.
John H.
Never trust a grinning idiot holding a big hammer!
-
- 100% FORDified!
- Posts: 22329
- Joined: Sun Aug 28, 2005 8:17 pm
- Location: Kansas, Ottawa
- Contact:
i cant make it to the junkyard tomorrow. i have to cut wood. i'm out. i will check tues or wed if its not snowing or anything. the last guy i talked to want 15.00 each for them and i thought that was high for used ones. but he had them. i've been trying to get in this new yard that has finally opened back up. and i just need time to go there when they have time too. have you tryeid auto zone oreillys or partsamerica they are all on line you can look them up. parrts america can get almost anything.
- boots
- Preferred User
- Posts: 411
- Joined: Sat May 21, 2005 5:13 pm
- Location: Illinois
ive tried auto zone, they said they could not get them, ill try the other 2 in a few minutes. When ever you get to the junk yard just post here, no rush , my truck is not going going anywhere for about a month!fordman wrote:i cant make it to the junkyard tomorrow. i have to cut wood. i'm out. i will check tues or wed if its not snowing or anything. the last guy i talked to want 15.00 each for them and i thought that was high for used ones. but he had them. i've been trying to get in this new yard that has finally opened back up. and i just need time to go there when they have time too. have you tryeid auto zone oreillys or partsamerica they are all on line you can look them up. parrts america can get almost anything.
Ethan
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
67 f100 - 4"lift - cut fenders - 36 TSL's
390/3spd/9"
68 f250 - 390/np435
Raised d24
'79 dana 60 front
welded 60 rear
buildup in progress
http://www.fordification.com/forum/view ... 835#136835
69 f100- Parts truck
-
- Preferred User
- Posts: 257
- Joined: Sun Nov 14, 2004 11:22 pm
- Location: California
re: tie rods
Check out this site.
http://www.federal-mogul.com/cda/channe ... 10,00.html
Federal Mogul bought out mega companies. Moog is one of those companies that makes chassis stuff. If you can find the part number, you'll have a better chance at finding it at parts houses. If you do your homework now, it'll save you the grief of dealing with those computer punching idiots at Kragen, etc. Who needs to know if you have A/C if you're looking for a tie rod?
http://www.federal-mogul.com/cda/channe ... 10,00.html
Federal Mogul bought out mega companies. Moog is one of those companies that makes chassis stuff. If you can find the part number, you'll have a better chance at finding it at parts houses. If you do your homework now, it'll save you the grief of dealing with those computer punching idiots at Kragen, etc. Who needs to know if you have A/C if you're looking for a tie rod?
-
- Preferred User
- Posts: 257
- Joined: Sun Nov 14, 2004 11:22 pm
- Location: California
re: tie rods
D'oh! I should have looked at your link before I opened my big mouth.